tag:blogger.com,1999:blog-1760465248680296780.post8123888206990391697..comments2023-09-28T00:36:53.151-07:00Comments on Anything Goes: FS-T6 firmware upgradeMichal Khttp://www.blogger.com/profile/05712646808155487704noreply@blogger.comBlogger9125tag:blogger.com,1999:blog-1760465248680296780.post-42178179907933635172023-04-25T18:23:40.153-07:002023-04-25T18:23:40.153-07:00Hey i had soft bricked my tx and don't know ho...Hey i had soft bricked my tx and don't know how to get back the original firmware any help with that I'm not particularly good with embedded systems... I was just playing around with the normal jumpers and had soft bricked and any way to get back the original firmware without hacking Vineethttps://www.blogger.com/profile/16012928162688195548noreply@blogger.comtag:blogger.com,1999:blog-1760465248680296780.post-12718435307236772322017-09-02T16:10:02.809-07:002017-09-02T16:10:02.809-07:00I do not know why it failed via the cable. Chances...I do not know why it failed via the cable. Chances are the hardware is still ok.<br /><br />One recovery method would be to get the STDiscovery board and connect the SWD debugger cables as explained elsewhere, see:<br /><br />http://minkbot.blogspot.com/2014/10/fs-t6-and-swd-hack.html<br /><br />Yes, a real hacking I am afraid.Michal Khttps://www.blogger.com/profile/05712646808155487704noreply@blogger.comtag:blogger.com,1999:blog-1760465248680296780.post-21889816490552454422017-05-12T23:43:52.235-07:002017-05-12T23:43:52.235-07:00I Also have this problem..Is it dead..Or can it be...I Also have this problem..Is it dead..Or can it be fixedAnonymoushttps://www.blogger.com/profile/06710662802371958357noreply@blogger.comtag:blogger.com,1999:blog-1760465248680296780.post-37578865595482377172016-08-21T08:33:41.144-07:002016-08-21T08:33:41.144-07:00Hi Michal, I was able to connect radio control via...Hi Michal, I was able to connect radio control via FS CT6B cable to try to change the firmware.<br />Unfortunately, after erasing all memory, I could not install the new firmware. <br />Now the radio control is death, i push on power button, but nothing happens. Now I can not install anything to the normal and easy way. Clearly I will need to open the box, but not clear to me how to connect to memory and to install the new firmware.<br />Thank you in advance!Anonymoushttps://www.blogger.com/profile/16727903947063634269noreply@blogger.comtag:blogger.com,1999:blog-1760465248680296780.post-20335793711303827322015-08-26T22:07:45.085-07:002015-08-26T22:07:45.085-07:00Lucio,
Sorry for the delay, vacation time...
&quo...Lucio,<br /><br />Sorry for the delay, vacation time...<br />"failed to init the device" - potential porblems: <br />- using wrong COMx port (I suppose you are on Windows?)<br />- connections are wrong (GND not well connected or sth swapped - your serial adapter has different cable color scheme)<br /><br />I advice you to purchase the original CT6B cable as it comes with correct plug.Michal Khttps://www.blogger.com/profile/05712646808155487704noreply@blogger.comtag:blogger.com,1999:blog-1760465248680296780.post-45203936826771424782015-07-12T07:13:17.098-07:002015-07-12T07:13:17.098-07:00Hi
i try to looking for a chip stm32f100 for this...Hi <br />i try to looking for a chip stm32f100 for this TX , but i can not find it in my country , so i can replace by chip stm32f103 ? it is same pin .<br /><br />i have to change code ?minhthienhttps://www.blogger.com/profile/00508259631320055066noreply@blogger.comtag:blogger.com,1999:blog-1760465248680296780.post-85507895283573080352015-06-02T21:04:35.968-07:002015-06-02T21:04:35.968-07:00I made connections correctly. I chose the firmware...I made connections correctly. I chose the firmware update mode the display menu. However in charge stm32flash COM5 get Failed to init device. Can you help me ??Lúcio Andréhttps://www.blogger.com/profile/15999921583695770299noreply@blogger.comtag:blogger.com,1999:blog-1760465248680296780.post-15230653704078800542015-05-24T09:03:19.225-07:002015-05-24T09:03:19.225-07:00Yes, no need for vcc. The transmitter should be se...Yes, no need for vcc. The transmitter should be self-powered (batteries/wallward).Michal Khttps://www.blogger.com/profile/05712646808155487704noreply@blogger.comtag:blogger.com,1999:blog-1760465248680296780.post-6686684757135061412015-05-16T17:57:08.113-07:002015-05-16T17:57:08.113-07:00you do not connect the vcc ?? only the gnd, Rx and...you do not connect the vcc ?? only the gnd, Rx and Tx ??Lúcio Andréhttps://www.blogger.com/profile/15999921583695770299noreply@blogger.com